It is currently Wed Dec 25, 2024 12:52 pm

All times are UTC - 6 hours





Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: RGB lighting
PostPosted: Wed Apr 05, 2017 4:07 pm 
Offline
Team Axis

Joined: Thu Dec 03, 2015 8:54 am
Posts: 86
Location: Higgins lake, Michigan
I'm going to some RGB speaker lighting for a spring boat project and was wondering what wire and connectors everyone here found that worked the best and didn't break the bank. I'm going to light the 4 Icon 8 tower speakers and bought XS650's with RGB to replace the 65's then planned on the wet sounds rgb controller for now.

_________________
2016 T22 409 Black/metallic yellow


Top
 Profile  
 
 Post subject: Re: RGB lighting
PostPosted: Thu Apr 06, 2017 11:39 am 
Offline
Team Axis
User avatar

Joined: Sun Jun 16, 2013 11:19 pm
Posts: 263
I'd use this wire: https://www.monoprice.com/Product?p_id=13730 (4 conductor 18 awg)

I'd cut these in half and solder one side to the leds and the other side to the wire going to the controller. http://www.ebay.com/itm/10-Pcs-10mm-4-P ... Swn8FXSRAH

Then put a dab of silicone over the solder joint and heat shrink over that.


Top
 Profile  
 
 Post subject: Re: RGB lighting
PostPosted: Thu Apr 13, 2017 9:28 am 
Offline
Team Axis

Joined: Thu Jun 16, 2016 12:34 pm
Posts: 191
Just curious how you're wiring everything together, are you going to run the RGB wires together in series to an already existing wire to give them power or are you running each LED strip back to a controller individually?

I'm thinking about doing LED cupholders and really not sure how to power them. I know there's a better way than running all 16 cup holders directly to the interior lights switch. I'm just not sure how to do it properly?

_________________
2016 Axis T23 w/410 ACME 2249 prop (WakeMakers 825# rear kit, WakeMakers ExactFit bow bag)


Top
 Profile  
 
 Post subject: Re: RGB lighting
PostPosted: Fri Apr 14, 2017 11:36 am 
Offline
Team Axis
User avatar

Joined: Sun Jun 16, 2013 11:19 pm
Posts: 263
You will wire in parallel. Run a couple of "mains" from your controller to your rgb zones, then branch off of those to each particular rgb location. Think trunk of tree to branches.


Sent from my iPhone using Tapatalk


Top
 Profile  
 
 Post subject: Re: RGB lighting
PostPosted: Sat Apr 15, 2017 8:44 am 
Offline
Team Axis

Joined: Thu Jun 16, 2016 12:34 pm
Posts: 191
I like kinda get it, and I see wiring diagrams, but I don't like real world get it. How do i connect the wires physically together in a chain? Splice? Twist on connector? Butt connector? A pic would be really really helpful.

I was thinking about hooking into my interior led wiring and just using that switch and forego RGB.

_________________
2016 Axis T23 w/410 ACME 2249 prop (WakeMakers 825# rear kit, WakeMakers ExactFit bow bag)


Top
 Profile  
 
 Post subject: Re: RGB lighting
PostPosted: Mon Apr 17, 2017 2:47 pm 
Offline
Team Axis
User avatar

Joined: Sun Jun 16, 2013 11:19 pm
Posts: 263
butt connectors will work. do the input in one end and several outputs in the other end (original wire plus a few "branches").


Top
 Profile  
 
 Post subject: Re: RGB lighting
PostPosted: Thu Apr 20, 2017 10:50 am 
Offline
Boater

Joined: Tue Jul 12, 2016 6:00 pm
Posts: 46
I'm currently doing the same project with my 4 Rev 10's. I purchased the 4 Wetsounds RGB LED rings and the RGB brain/controller. Will be the first time doing a project like this so any help will be great!

_________________
2016 T23, 5.7L 350, 3093 Prop/15x12.5 w/ 165 cup, Wake Makers 825lbs PNP rear lockers, Sumo Sac 650lbs PNP, 2nd Ronix Eight.3 650LB bow, Ronix Eight.3 800LB Floor Bag


Top
 Profile  
 
 Post subject: Re: RGB lighting
PostPosted: Sun Apr 23, 2017 7:38 am 
Offline
Team Axis

Joined: Sun Sep 16, 2012 8:55 am
Posts: 375
Location: Central Texas
Nickleej wrote:
I'm currently doing the same project with my 4 Rev 10's. I purchased the 4 Wetsounds RGB LED rings and the RGB brain/controller. Will be the first time doing a project like this so any help will be great!



I did this on my old Axis... pay extra for the swivel clamps; as the connectors are pre-wired and you can mount w/o the speaker attached... just my $0.02...

Haven't heard if they've been redesigned, but I had to drill small holes for the wire between the ring and speaker housing... that was nerve racking.

_________________
-aha-


18 Monterey 278SSC


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 21 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: