Service Required

gibbs114 · **Posted:** Sun Jul 24, 2016 1:00 pm

Boat has 109hrs on it. I changed the oil myself about 100hrs. It's now giving me a service engine required message and beeping. Is there a way to turn this off without taking to dealership?

Sent from my iPhone using Tapatalk

dezul · **Posted:** Sun Jul 24, 2016 3:34 pm

Did you check the fault code?

gibbs114 · **Posted:** Sun Jul 24, 2016 6:11 pm

Yes it shows nothing.

Sent from my iPhone using Tapatalk

80AMT23 · **Joined:** Thu Jun 16, 2016 12:34 pm **Posts:** 191

I had the same issue on mine. Initially PCM said there was a software update that fixed an issue with the water intake manifold temperature alarm threshold being set to low. It's not actually a problem, but annoying. There's a software update your dealer can do. I had them do it on mine, and took it out that same day and the alarm went off again.

Went out 2 more days and ran it hard, no alarms at all. Boat is back in the shop for the 20 hour service and they're working with PCM on it. I should have the boat back by Tuesday and I'll give an update.

chaser720 · **Joined:** Mon Feb 15, 2016 1:31 pm **Posts:** 90

Pull the positives on the batteries overnight. This should reset the service required error. It will keep coming on if there is still a problem but it shouldn't return if it was a one time thing. If it does pop back up, immediately check the fault code.

I've heard that a couple of cold starts without seeing the error will reset it too but the battery disconnect worked for me.

get_sum · **Posted:** Mon Jul 25, 2016 9:36 am

What code exactly were you seeing? I've seen these codes a few times and this weekend it was on longer and caused me to go into limp mode. I pulled the impeller and swam under to check the intake for debris. All was fine.

ECM: SPN 441 FMI 15
ECM: SPN 442 FMI 15 (5 times)

Sent from my iPhone using Tapatalk

shawndoggy · **Joined:** Sun Jun 16, 2013 11:19 pm **Posts:** 263

http://dealer.pcmengines.com/assets/Att ... terial.pdf

Sent from my iPhone using Tapatalk

gibbs114 · **Posted:** Tue Jul 26, 2016 5:20 am

Also when the light first comes on the boat seams to temporarily lose power but picks right back up.

Sent from my iPhone using Tapatalk

chaser720 · **Joined:** Mon Feb 15, 2016 1:31 pm **Posts:** 90

gibbs114 wrote:

Also when the light first comes on the boat seams to temporarily lose power but picks right back up.

Sent from my iPhone using Tapatalk

I would try to read that code ASAP. Losing power points more towards a malfunctioning part than a bad sensor something.

Might look into buying one of these if you're a good drive from the dealership. It would help to figure out if you have a serious issue or more of an annoyance. They are about $600 though.
http://www.rinda.com/marine/marine.htm

chaser720 · **Joined:** Mon Feb 15, 2016 1:31 pm **Posts:** 90

get_sum wrote:

What code exactly were you seeing? I've seen these codes a few times and this weekend it was on longer and caused me to go into limp mode. I pulled the impeller and swam under to check the intake for debris. All was fine.

ECM: SPN 441 FMI 15
ECM: SPN 442 FMI 15 (5 times)

Sent from my iPhone using Tapatalk

Pretty sure that's the error code the 2015 PCM engines were seeing before the software reflash. What year are you?

http://www.ambil-yam.co.il/files/pdf/PC ... manual.pdf

DTC 1416 - Exhaust Manifold Water Temperature (EMWT) Sensor 2 Higher Than Expected
Stage 1
SPN - 442; FMI - 15

Axis Wakeboard Boat Forum

Service Required

Who is online